Water play area

-+

Public Playgrounds

Manual

Suitable for ages 5+
,
public playgrounds, etc.,
manual activities.

-

11.55 m

8.40 m

4.80 m

14,55 m

11.40 m

4.80 m

140.00 kg

1885.00 kg

1.80 m

0.20 m, 1.15 m, 1.60 m, 1.80 m

37 pieces - 0.40 x 0.40 x 0.40 m volume: 0.07 m3

2 pieces - 0.30 x 0.30 x 0.40 m volume: 0.04 m3

-

-

-

-

2 pers.

10 h

Installation time 2 fitters 10 hours each (without creating the foundation without water connection)

Technical data
Total height: approx. 4.80 m
Base area: approx. 8.40 x 11.55 m
Minimum space: approx . 11.40 x 14.55 m (116 m²)
Platform height: 0.20 / 1.15 / 1, 60 / 1.80 m
Weight: 140 kg heaviest single part
1885 kg in total

Support
post Support post made of Robinia plywood, milled cylindrically, Ø 120 mm. Unprotected end grain surfaces are covered with non-detachable post caps made of stainless steel. Posts that are flush with the platform are not provided with post caps.
Pipe stand made of stainless steel for the foundation and mounting of robinia round wood posts, Ø 120 mm, below the playing level.

Platform floors Platform floors
made of boards, 30 mm thick and all-round square timber beams 45 x 100 mm. The dried robinia lumber is planed, chamfered and free from rotten branches. Non-positive floor fastening thanks to special stainless steel brackets with a continuous bolt connection. Pump platform also with profiled stainless steel sheet.

Attachments
– ramp 2.40 mx 1.60 m, incline 0.10 m, made of profile boards 95 x 30 mm
– climbing
rungs (cranked) made of stainless steel pipe, Ø 33.7 mm – iron railing, anti-roll, made of stainless steel pipe, Ø 33.7 x 2 mm
– tandem railing 0.80 m / made of stainless steel tube, Ø 33.7 x 2 mm
– vertical handle as a climbing aid made of stainless steel tube, Ø 33.7 x 2 mm
– mesh balustrade made of stainless steel tube, Ø 33.7 x 2/25 x 2 mm , one-piece welded construction
– table 0.80 x 0.80 m, made of colored, highly weather-resistant HPL laminate board, 15 mm / red
– tent roof, 6 x 0.80 m / inclination 45 °, made of brown, highly weather-resistant HPL laminate board, 13 mm, with greyhound; Attachment to the roof frame made of stainless steel tube Ø 33.7 x 2 mm
– Wobble steps, 0.80 mx 2.40 m on tandem traverses, running timbers made of robinia Ø 10 cm, fine-linked handrail chains made of stainless steel

K&K water pump Article No. 0-33130-001 Suction
pipe connection 1 ¼ inch (pipe diameter at least ¾ inch), welded stainless steel construction, encapsulated pump housing, pump mechanics with roller and slide bearings, upper pump housing with handle must be removed e.g. during the frosty season, sealing cover (” Wintering plate “) for the remaining lower part of the pump is included.

Please note:
When connecting the water pump to a pressurized water line, the K&K valve combination (Art.No. 0-33190-000) is required.

If the water supply is intended to be temporarily interrupted (timer or similar), a negative pressure builds up in the line system when the pump continues to operate, which leads to the pump handle kicking back.
It is therefore imperative to prevent actuation of the pump handle (for example by using the pump lock item number 1040639).

In doing so, also observe the general data specified in the assembly instructions (distances, diameter of the lines, etc.); You can get these on request from K&K or directly as a PDF from our website at www.kaiser-kuehne-play.com.

K&K valve combination Article No. 0-33190-000
Device for direct connection of the water pump to a pressurized water line.
Incl. Fine filter for cleaning the water from suspended matter, dirt particles, etc. to prevent the diaphragm valves from becoming dirty and thus prevent malfunctions.
The valve combination should be installed and connected by a specialist installation company.

K&K terrace shell 1 drain
Base area: Ø 0.90 m
Total height: 0.14 m
Welded stainless steel construction with 1 water drainage opening, sheet thickness: min. 2 mm / pipe Ø 38 mm.

K&K water pipe 0.80 x 1.60 m
area: 0.80 mx 1.60 m
stainless steel pipe Ø 154 mm
Welded stainless steel construction with 1 beveled water drainage and 1 inlet opening, sheet thickness: min. 2 mm / pipe Ø 154 mm.

K&K water reservoir
base area: Ø 0.68 m
Welded stainless steel construction with 2 water drainage pipes. Rubber cone closure with lock for complete water withdrawal. Sheet thickness: min. 2 mm / tube Ø 33.7 mm.

K&K water gutter 1.60 m, 3 pieces
welded stainless steel construction 0.80 mx 1.60 m, sheet thickness: min. 2 mm / pipe Ø 38 mm. With connection for support posts, with stepless inclination for installation for the required gradient for the inlet and outlet of the water. Sloping spout.

Stowage flap, 3 pieces
freely positionable, handle made of stainless steel, sheet made of rubber with fabric insert. Clamping part for attaching to pipe Ø 38 mm

K&K water wheel
Base: 0.60 x 0.80 m
Height: approx. 0.90 m
Wheel: Ø 0.60 m
Welded stainless steel construction with post connection, prepared for the water channel. 12 blades, bevelled flat on the front side and enclosed by side walls. Sheet thickness at least 2 mm. Wheel bearings with roller bearings.

K&K terrace
shell 2 drains 90 ° / 180 ° Base area: Ø 0.90 m
Total height: 0.14 m
Welded stainless steel construction with 2 water drainage openings offset by 90 °, sheet thickness: min. 2 mm / pipe Ø 38 mm.

K&K water gutter 2.40 m
Welded stainless steel construction 0.80 mx 2.40 m, sheet thickness: min. 2 mm / pipe Ø 38 mm. With connection for support posts, with stepless inclination for installation for the required gradient for the inlet and outlet of the water. Sloping spout.

K&K Maxitisch 6 x 0.80 m with water valve
Base: 1.40 x 1.70 m
Height: 0.80 m
Hexagonal stainless steel construction with lockable rubber cone lock for damming, regulating or diverting water. Sheet thickness: min. 2 mm

K&K whirling table 0.80 x 1.60 m
Welded stainless steel construction with 5 pieces. adjustable HPL prisms as flow obstacles. Sheet thickness at least 2 mm, pipe Ø 33.7 mm or Ø 30 mm

Metal components: stainless steel.
The robinia wood is provided with a water-repellent, breathable protective coating. In addition to protecting against moisture, this treatment reduces cracking. The modular add-on parts introduce their forces directly into the support posts via a special adapter attachment. The screw connections are secured against unauthorized loosening with cover caps.

Foundations (on site)
37 pcs. 0.40 x 0.40 x 0.40 m
2 pieces. 0.30 x 0.30 x 0.40 m
Amount of concrete: 2.44 m³

Free fall height
1.80 m